Swimming Pool Filter Troubleshooting


Your Swimming Pool Cartridge Filter will not clear algae from the pool

The three filter types will clear up algae, provided it is not in a live state. Consult http://www.1800 Pools.com for the proper chemicals to help rid the algae. Most cartridge filter problems are caused by dirty, clogged or abused elements. Either clean the elements, or replace if torn or damaged.

Your Swimming Pool DE filter has short cycles when vacuuming

This is normal if the pool contains very dirty water. Backwash or regenerate and recharge more often. If there is a presence of live algae, add enough chlorine sanitizer to control this growth, then vacuum. The presence of alum or flocking agents will clog the filter. Vacuum so as to bypass the filter. Do not use flocking agents with DE filters.

Your Swimming Pool DE filter is leaking back into the pool

Be sure that the suspected material on the pool floor is actually DE. Pollen, chemical residue and plaster dust often look like DE. You may have a tear in your filter elements, replace if necessary. Make sure that you assemble the internal parts properly! Check for air leaks, as this will cause the system to leak DE back into the pool. If there are air leaks, install a check valve between the pump and the filter valve.

Your Swimming Pool DE filter is running at high pressure

The DE filter is loaded with too much debris or algae and needs backwashing or regeneration. If this problem persists and you notice the filter gauge pressure rising from 7 - 10 psi above your beginning pressure, you need to regenerate your filter.
Refer to your Owner's Guide for further instructions or consult your pool dealer for service.
Your pump output might exceed the design flow rate of the filter. Make sure the pump is correctly sized for your filter.
If there is algae in the pool, super chlorinate, backwash or bump/drain and recharge as needed. Make sure you are properly backwashing on your vertical grid filter.
Refer to your Owner's Manuals for instructions.

Your Swimming Pool DE filter short cycles even after I backwash

The filter elements may be clogged because of an accumulation of chemical deposits. Clogging is accelerated if chemicals are fed through the skimmer, operating your filter too long without DE after starting the pump, or operating the filter without DE. DE must be added as soon as the filter is full of water, and the pump is putting out a steady stream of water. Refer to your Owner's Guide for the amount of DE your filter requires. Biguanide based sanitizers (i.e. Baquacil, SoftSwim) can cause short cycling.

Your Swimming Pool Filter is noisy

An oversized pump may cause noise in your filter valve due to excessive flow. To test, hold your hand partially in front of any returns at the pool wall. If the noise subsides, this will confirm that the problem is excessive flow. It can be remedied by installing smaller eyeball fittings in the return(s), changing the pump impeller size in the pump, or change to a 2-inch control valve.

Your Swimming Pool Flow Valve leaks to Waste

The valve seat gasket inside the valve has become worn or loose. You may choose to do this yourself or contact your local pool dealer for service. How do you replace the gasket? You will need a new gasket, obtained from your local dealer, some Krazy Glue, and a sharp 1/8-inch wide flat bladed screwdriver.
NOTE: Mark the top and bottom of the valve with a marking pen. It's very important that you do not change the location of the cover when re-assembling. Remove the cover, usually six screws. Using the screwdriver, scrape out every last part of the gasket and cement, in order to get back to a clean flat surface. Put a fair amount of crazy glue on the flat side of the gasket. Place the gasket, flat side down, back into place let dry for one hour minimum.

Your Swimming Pool Sand Filter is running at high pressures

Follow the backwashing instructions in your Owner's Manual. The sand bed may be clogged with mineral deposits that will not backwash away. Some calcium based chlorines and other alternative sanitizers will build up in your sand bed, and will require more frequent backwashing and changing of the sand.
Before you replace all the sand in your filter, try removing approximately 1" of the top layer of the sand, replace with the exact amount of sand you removed.
Normal life span of the sand is about 4 - 5 years.
You may have to clean your filter system with a special filter cleaner, check with your pool dealer for proper procedures.
Check to see if there is a closed or partially closed valve along your return piping, open the valve.
Your pump may be too small to provide sufficient flow for proper backwashing. Your filter will function, but a lower design flow rate will cause your system to backwash improperly. Check the output of the pump to be sure that it equals your filter's design flow rate. Replace the pump if it is too small.
S.Merillat(r)

Visit http://www.1800pools to learn more about Pool Filter Care.

Steve Merillat has been in the Pool industry for 35 years. He started early on working for various Swimming Pool supply companies before ventured out in his own business. He pioneered many processes with the installation of pools that are used as industry standards today. He regularly holds seminars and classes on how to properly maintain your Swimming Pool. Visit www.1800pools.com


Please Rate this Article...                    Not yet Rated


More Articles From - Home | Shopping And Product Reviews | Home


© 2008 ArticleClick.com Free Articles - All Rights Reserved